Cars and vans › Brakes › Brake drag › Causes

Seized slide pins

A cause of brake drag on brakes with a floating caliper.

Test it

  1. While it drags, open the bleed screw on that caliperClose it at once, top up the reservoir and bleed that brake before the car moves.
    Wheel freesPressure is held further up: a hose, the rear regulator, the ABS unit or the master cylinder side.
    Still dragsThe fault is at the wheel itself.
  2. Pads out: slide the caliper on its pins by handCompare with the other side if you can.
    Stiff or will not moveSeized slide pins: this page.
    Slides freelyLook at a stuck piston or seal.
Why, in full

Fix it

  1. Hang the caliper up from the suspension with wire or a hook; it must never hang by its hose11.
  2. Clean both pins until they are bright and the holes back to bare metal12,2.
  3. Replace pins that stay stiff or are corroded, pitted, worn or stretched12,6,7.
  4. Refit them with fresh lubricant such as silicone brake grease; old copper paste can crust up2,17.
  5. Check that it cured the drag. If nothing changed, go back and look at the piston18.
Repairing it, in full

Most cars use a floating caliper, which has its piston on one side of the disc only. When you brake, the piston pushes the inner pad against the disc, and the reaction pulls the whole caliper body sideways on two slide pins, which brings the outer pad in from the other side. For this to work, and for the brake to let go again, the caliper has to be free to move on those pins. If rust, dried grease or a perished rubber boot stops it from sliding, the caliper can no longer centre itself and one pad keeps rubbing on the disc after you have lifted your foot.

How it shows up

The most reliable sign is uneven pad wear on one wheel. On a Jaguar XF the inner pad on the rear nearside had worn down to metal while the other pad was still fine, and the caliper on that side could not be slid by hand although the one on the other side could2,1. On a 2000 Jetta TDI crud had built up on the sliders, so the calipers no longer let go completely and the rear pads and discs had to be replaced3. Uneven wear alone does not prove the pins, though: in the same thread a 1999 Golf owner found his inner pad metal to metal while the sliders moved smoothly, and the crud was on the pad clips instead3. Which of the two pads wears out first depends on where the caliper sticks, and owners disagree about how to read it: on a Saturn Ion with a fast-wearing outer pad, one poster blamed frozen pins and another disputed that4.

InnerDiscOuter

Pins free: both pads wear at the same rate.

InnerDiscOuter

Pins seized: one pad worn to the metal, the other nearly new.

The pattern the owner of a Jaguar XF found1. Which pad goes first depends on where the caliper sticks.

In the reports, owners noticed something else first. A grinding noise that goes on after the pedal is released, or a squeal with the foot off the brake that stops under light braking, are common first reports2,5. On an MX-5 one dragging rear brake made the car wander on the motorway in a way the owner took for tramlining6, and on a 1990 Cherokee the only complaint was poor fuel economy, which improved dramatically once the pins were replaced7. Vibration under braking is reported as well, and on an Aveo lubricating the guides cured it8.

Telling it apart from other caliper faults

A caliper can stay on for several reasons, and seized pins are only one of them, so it pays to rule out pressure first. While the brake is dragging, open the bleed screw on that caliper. If the wheel frees as soon as the screw is open, the brake was being held by pressure from further up: a hose, the rear pressure regulator, the ABS unit or the master cylinder side. How much fluid comes out does not decide it: on a Civic with both fronts dragging only a little came out, yet the fault was the brake pedal, held down by a misfitted brake light switch9. If the wheel still drags with the screw open, the fault is at the wheel itself. Close the screw at once, top up the reservoir and bleed that brake before the car moves. Be careful with a bleed screw that has not been opened for years, since one on a Corolla broke off and left the caliper impossible to bleed10.

The direct test is to take the pads out and move the caliper on its pins by hand. It should slide smoothly without much force, as the good side did on the Jaguar1. If it does not, take the pins out of their boots and look at them. A piston that is hard to push back points instead to a stuck piston or seal, which can occur together with this fault.

Repairing it

Before you start, hang the caliper from the suspension with wire or a hook, because it must never hang by its hose11. Then pull out both pins and clean them until they are bright. A Sprinter owner was told to clean them first and only replace them if they remained stiff12, while the Jaguar owner cleaned the holes back to bare metal with a wire bore brush and fitted new pins and boots2. New pins are the right answer when they are corroded, pitted or worn, as on the MX-56, and pins can stretch as well, which is what happened on the Cherokee7. Some Sprinter calipers need a repair kit with a new sleeve and rubber collar13, and one owner found the bore in the carrier itself so worn that it had to be machined and fitted with a bushing14.

Refit the pins with fresh lubricant. The Jaguar owner used silicone brake grease2, others report copper paste, graphite paste and KMP-100015,16,17, and one reply warns that old copper paste can crust up and cause sticking of its own17. Finally, check that the job actually cured it. On one car a new disc, new pads and greased guide pins made no difference, and the owner was left asking about a new caliper18, which is the sign to go back and look at the piston.

What owners did

CarWhat was wrongWhat was doneResult
Jaguar XF, rearPins seized in hardened boots full of crudNew pins and boots, holes cleaned to bare metal, silicone greaseCaliper slides easily again2
Mazda MX-5, rearSlider pins corrodedNew slider pinsReported as the repair6
Jeep Cherokee 1990Pins stretchedPins replacedFuel economy improved dramatically7
Mercedes Sprinter, frontPin had worn its blind bore in the carrierBushing machined into the borePistons work evenly again14
Chevrolet AveoVibration under brakingGuides lubricatedHelped8
VW Jetta TDI 2000, rearCrud on the caliper sliders, calipers not letting goRear pads and discs replacedReported as the repair3
Unnamed carOne wheel overheating and smellingNew disc and pads, guide pins greasedNo change, caliper next18

Keeping it from coming back

Pins seize because they are rarely looked at, so the simplest prevention is to clean and grease them whenever the pads are changed19. Owners who drive in salt or leave vehicles standing do it more often: one VW driver cleans the sliders roughly every 40K on his odometer, when the caliper starts to hang up and squeak3, a Sprinter owner strips the calipers and carriers every two years20, and a Xedos owner was advised to do the rear pins every six months21. A torn boot lets water straight in, so it is worth replacing as soon as you see one. citation needed

Where it comes up most

Rusted guides on the rear brakes come up repeatedly on the Mercedes Sprinter, particularly after standing or a winter22,20. Owners of 1999 to 2001 VW Jetta, Golf and New Beetle TDIs report rear pads wearing out well before the fronts; several blamed crud on the sliders, while one Golf owner found it on the pad clips instead3.

Further reading

Sources

  1. Changing Brake pads and Discs – Jag XF (With pictures) | Page 2 | XF Forum, xfforum.co.uk
  2. Changing Brake pads and Discs – Jag XF (With pictures) | Page 3 | XF Forum, xfforum.co.uk
  3. rear passenger wheel - stuck and brake pad worn out, forums.tdiclub.com
  4. *UPDATE caliper replacement or something more serious?, community.cartalk.com
  5. 2007 Ford Edge SEL AWD - Quite a few problems - need advice | Ford Forums, fordforums.com
  6. Slightly off?, forum.mx5oc.co.uk
  7. Advice for Buying a Car, community.cartalk.com
  8. авео т250, при скорости 80+ при торможении биение руля, у кого-то было такое? Слышал что у них это болезнь, оно лечиться как то, aveo-auto.ru
  9. Sticking Front Brakes, community.cartalk.com
  10. '97 Corolla brakes dragging...bleed 'em?, community.cartalk.com
  11. "Underdesigned" Brakes Likely Causing Problem (Newspaper Column), community.cartalk.com
  12. einseitiger Verschleiß an Bremsbelägen, sprinter-forum.de
  13. Geräusch - Vorderachse (4x4), sprinter-forum.de
  14. Bremssattel Fragen, sprinter-forum.de
  15. Bremsen hinten links - Geräusch und Wärmeentwicklung, sprinter-forum.de
  16. Sprinter Bremssattel Probleme, sprinter-forum.de
  17. Bremsen lösen nicht, sprinter-forum.de
  18. Problemos su stabdziu sistema, uscars.lt.figa.serveriai.lt
  19. Sprinter schleifen beim rechts Lenken, sprinter-forum.de
  20. Vorbeugende Wartung Bremsen, sprinter-forum.de
  21. Вебрирует педаль тормоза!!!!, forum-xedos6.ru
  22. Pfeiffen bei langen Autobahnfahrten -> Bremssattel Hinterachse?, sprinter-forum.de