Cars and vans › Brakes › Brake drag › Causes

Rear pressure regulator holding pressure

A cause of brake drag on the rear brakes of vans, pickups and cars with a valve that limits rear brake pressure.

When a vehicle brakes hard, its weight shifts forward and the rear wheels carry less load, so the pressure the front brakes need would lock the rears. A proportioning valve in the line to the rear brakes therefore passes full pressure at first and lets the rear pressure rise more slowly once it passes a set point. On most cars it sits close to the master cylinder, either inside a combination valve that also carries the brake warning switch or screwed into the master cylinder's outlets to the rear brakes, and cars whose ABS unit shares out the braking between the axles (electronic brakeforce distribution) have no separate valve at all. Vans and pickups, whose rear axle load changes a great deal between empty and loaded, use a load-sensing version: a linkage from the axle, ending in a spring on a lever at the valve, tells it how far the body has settled on its springs, and the more the vehicle is loaded, the more pressure it lets through to the rear1,2,3. On the Mercedes Sprinter and the VW LT the valve is known as the ALB (automatisch lastabhängige Bremskraftregelung) or Bremskraftregler, and it sits on the body near the rear axle with its linkage running down to the axle1,4,2. Cars with converted brakes may carry an adjustable valve with a knob, as an Opel GT with rear discs does5.

For the rear brakes to let go, the fluid that went out to them has to flow back through the valve to the master cylinder when you lift your foot. If something inside the valve sticks, it can let pressure through to the brake and then block or slow the way back, so the rear brakes stay applied with no foot on the pedal, in the same way as a hose that has failed inside. The owner of a Sprinter 311 CDI found exactly this: something in his regulator let pressure through to the right rear brake but released it only very slowly or not at all6. On a Sprinter 308 CDI both rear brakes locked after a few applications, and the owner found the nut on the regulator's linkage screwed on so far that the linkage was under constant tension; slackening it cured the drag7. The thread does not explain how that tension kept pressure in the brakes. These two vans are the only cases where a regulator was found holding the brakes on, and on a Sprinter 313 CDI it was suspected without being confirmed8.

A related fault does not cause drag: the regulator's lever rusts solid in one position, and the valve keeps working at that fixed setting. Stuck in the empty position, it leaves a loaded van braking too weakly at the rear2; stuck fully open, it brakes the rear as if loaded even when empty, so that on one VW LT the engine could be stalled in gear against the braked rear wheels of the lifted, unloaded axle with the old regulator and no longer with the new one9. It turns up at the roadworthiness inspection (TÜV in Germany, MOT in Britain) on Sprinters, LTs and Iveco vans, often on campers and other vans that always carry about the same load or stand through the winter10,11,2,12. Owners free the lever by unhooking the linkage, clamping locking pliers on it and working it with penetrating oil and light taps until it moves, which on one LT took four days of spraying twice a day, and then coat it with cavity wax, the soft anti-rust wax sprayed into body sections2,10. A lever rusted onto its shaft can break off13. Freeing one changes the rear braking sharply: after a Sprinter owner freed his, the first test stop nearly pulled him out of the seat14, so have the setting and the rear braking checked afterwards. A seized lever found while hunting a drag is not proof that the regulator causes the drag.

How it shows up

The valve only acts on the rear brakes, so the drag shows as hot rear wheels while the fronts stay cool. On the 311 CDI the fault sat inside the regulator and held only the right rear wheel's circuit6, while on the 308 CDI the fault was in the linkage and both rear brakes locked together7.

The brake comes on with use and stays on. On the 311 CDI it set itself while driving: about 3 km after a fuel stop there was a cloud of smoke behind the van, the disc was glowing and the pad burning, and the owner had already felt the van down on power and put that down to poor diesel. After he had fitted new calipers, discs, pads and hoses, the same wheel locked again at the next brake application, and the fault also happened with the engine and ignition off6. On the 308 CDI the van drove normally after the pressure had been let off until the first stop; then the pedal felt firmer with a shorter travel, and by the third application the rear brakes had locked again7.

Both Sprinters had a recently fitted regulator. The 311 CDI's was a new Bosch part, the same make as the original, fitted about a year and a half before, and the 308 CDI's had just been changed6,7. Recent work on the regulator or its linkage is a reason to look at it, not a reason to rule it out.

Telling it apart from other causes

Start with the test every hydraulic cause shares, and do it while the brake is dragging, because it only works then. Open the bleed screw on that wheel. If the wheel frees as soon as the screw is open, the brake was being held by pressure from further up. On the way from the pedal to a rear wheel that pressure can sit at the pedal and brake light switch, the booster and pushrod, the master cylinder, the ABS unit where one is fitted, the rear pressure regulator, or the flexible hose; whether the ABS unit or the regulator comes first in the line varies by car. If the wheel still drags with the screw open, the fault is at the wheel itself. How much fluid comes out does not decide it; whether the wheel frees does. Close the screw at once, top up the reservoir and bleed that brake before the vehicle moves. On the 311 CDI and on a 1995 Sprinter 312D the wheel freed at the bleed screw, and a new caliper changed nothing; the 312D's old caliper turned out to move freely6,8. The regulator feeds only the rear brakes, so if the fronts are hot as well, it cannot explain them and the master cylinder side is the place to look.

To find where the pressure is held, open the joints one at a time, from the wheel upwards. The brake has to be dragging again before each step, because every opened joint lets the pressure go. A wheel that frees at once when a joint is opened clears everything between that joint and the wheel. A part that lets pressure back only slowly can still let the brake go a while after a joint further up is opened, so a wheel that frees slowly clears nothing. The 312D owner worked this way: he let the right rear brake lock, opened the line at the regulator's outlet and the pressure dropped, pressed the pedal until the wheel locked again, opened the line at the regulator's inlet, and the pressure dropped there too; he concluded the regulator was passing fluid back and turned to the ABS unit8. The 311 CDI owner opened the right rear port at the ABS unit, the brake freed, and he took it for a sticking ABS valve, yet the cause turned out to be his regulator6. Neither says how quickly the wheel freed. Releasing pressure at the regulator's inlet does not clear a regulator that lets pressure back slowly, and no owner describes a test that tells such a regulator apart from a sticking valve in the ABS unit. Tighten each joint straight away, and bleed the brakes afterwards, using the scan tool routine on ABS vehicles that need one.

What can be checked directly is the outside of the regulator. Its lever should move a little when a helper presses the pedal hard, which can be seen lying under the van15,14, and with the linkage unhooked it should move by hand1. Check how the linkage is set as well: on the 308 CDI it looked free and moved easily, yet the nut on it was screwed on so far that there was still a lot of tension on it after many turns7.An Opel GT shows why the whole line has to be checked before the regulator is blamed. At a car show the rears locked and ran red hot while the fronts stayed cool, and the owner first blamed his adjustable proportioning valve, whose knob he found had turned; he reset it and wired the knob5,16. The brake parts maker Wilwood replied that rear brakes which drag and hold pressure point to a master cylinder that does not return fully5. Later the owner wrote that the drag may have come from the pedal not returning: he reproduced it in his driveway with the pedal hitting the power steering unit, so that the brakes dragged until he pulled the pedal back by hand, and removing the shims he had fitted, then loosening and realigning the bolts, stopped the pedal from hitting it17,18. The car has rear discs and a residual check valve in the master cylinder's rear outlet17,18.

Repairing it

Letting the pressure out at a bleed screw or a line nut frees the wheel only until the next time you brake: the 308 CDI's rears were locked again by the third stop7. A Sprinter that someone drove on with a dragging rear brake ended with smoke pouring from the rear, a ruined disc and pads, and fire brigade, ambulance and police on the motorway8. A vehicle whose rear brakes hold pressure stays parked until the cause is found and fixed.

Where the linkage holds the valve, setting it correctly is the repair. The 308 CDI owner undid the nut until the tension was gone and let the trapped pressure out at the bleed screws, and afterwards the warning lamp was off, the pedal felt normal and full stops from 10 km/h in the yard worked; he still planned to have the brakes checked before the next trip7. Letting pressure out at a bleed screw lets air in: close each screw at once, top up the reservoir and bleed the brakes before the vehicle moves. On the Sprinter the setting values are on a label inside the front passenger door, a table of rear axle load against the dimension of the regulator's spring10,3. The final setting is a workshop job, done by measuring brake pressure at the wheel or on a roller brake tester, the rollers that measure each wheel's braking force3,19. One owner who replaced his regulator himself measured the old one with a vernier caliper, set the new one to the same dimension and checked that it worked in the middle of its travel when the lever was in the middle, and it passed inspection3. One reply advises measuring from the end of the thread to the nut before taking the spring apart, so that the same preload goes back on20.

Where the valve itself holds the pressure, owners replace it. On the Sprinter the regulator carries four brake lines, so the job opens the hydraulic system and ends with bleeding the brakes4, followed by the setting described above and a check of the rear braking. Removing the regulator and joining its lines is not allowed in general: replies on the Sprinter forum point out that the empty rear axle would then be overbraked and that the inspection will not pass it4. The exception is a vehicle whose rear axle is always heavy. One camper owner joined the lines of his 307D's regulator with a union and the inspector accepted it once the axle load was proven, and others had the regulator fixed fully open with the inspector's approval on the same condition10,11. Some later Sprinters were built without the regulator, listed as equipment code B90, which means the regulator is deleted; a reply ties this to the version of their stability control (ESP), which cannot simply be retrofitted to a van that has a regulator4.

On an adjustable valve, set the knob and lock it so that it cannot turn; Wilwood suggested a drop of removable thread-locking fluid or safety wire from the knob to the brake line nut5. The Opel GT's owner set his to about three quarters of full pressure, the middle of its range, and wired the knob through a hole drilled in it16, but as the tests section explains, his drag was later tied to the pedal rather than the valve.

What owners did

CarWhat was wrongWhat was doneResult
Mercedes Sprinter 311 CDI (W903), rear rightBrake locked at every application, disc glowing after 3 km; regulator about 1.5 years oldNew calipers, discs, pads and hoses; ABS valve suspected, then everything tested againRegulator found holding the right rear circuit; owner reports the problem solved6
Mercedes Sprinter 308 CDI 2003, both rearRears locked by the third application, firm pedal; nut on the new regulator's linkage far too tightNut undone until the tension was gone, pressure let out at the bleed screwsBrakes and warning lamp normal on yard tests7
Opel GT, both rearRears locked and red hot at a show; owner first blamed the adjustable proportioning valveValve reset and knob wired; later the pedal was found hitting the power steering unit and the shims behind it were removedOwner later tied the drag to the pedal not returning, not the valve5,16,17
Mercedes Sprinter 312D 1995, rear rightBrake held after winter storage, pressure at the bleed screwNew caliper; lines opened at the regulator's outlet and inlet, pressure released at bothPressure released at the regulator's inlet; regulator not confirmed as the cause. A full stop freed it for about 10 km8
Mercedes Sprinter 313 CDI 2001, rear rightBrake held after hard pumping; regulator renewed a year beforeNew caliper and hose, line blown throughNo change; owner turned to the ABS unit8

Keeping it from coming back

Both Sprinters that dragged had a regulator that had recently been changed6,7, so after any work on the regulator or its linkage, set it to the values on the door label and have the rear brakes measured. The same applies after a suspension change: extra springs, air suspension or a lift change the ride height the regulator reads, so it has to be reset, or raised on an adapter plate21,20,11. One reply puts seized regulators down to years without brake servicing and water in the fluid, and recommends changing the brake fluid along with a new regulator20.

Further reading

Sources

  1. Gestänge zum Bremsverteiler Hinterachse?, sprinter-forum.de
  2. 212D Bremsdruckregler: Bitte ein Foto!, sprinter-forum.de
  3. ALB-Regler Federstange einstellen, sprinter-forum.de
  4. ALB Regelgestänge demontieren, sprinter-forum.de
  5. Gordo's Banana Completed??? | Opel GT Forum, opelgt.com
  6. Betriebsbremse hängt fest, sprinter-forum.de
  7. Beide Hinterbremsen fest, Druck baut sich nicht ab, sprinter-forum.de
  8. Bremse hängt, Druck in der Leitung geht nicht weg..., sprinter-forum.de
  9. ALB - Bremskraftregler Hinterachse - ohne Last, sprinter-forum.de
  10. Bremskraftregler, sprinter-forum.de
  11. ALB gängig machen, sprinter-forum.de
  12. Brake Load Sensor Linkage, ivecoforums.com
  13. Hebel abgebrochen (hat irgendwas mit der Bremse zu tuen) was ist das für ein Bauteil..., sprinter-forum.de
  14. bremsen, sprinter-forum.de
  15. Probleme mit der Bremswirkung – Feststellbremse, Betriebsbremse, Bremskraftregler, sprinter-forum.de
  16. Gordo's Banana Completed??? | Page 2 | Opel GT Forum, opelgt.com
  17. Gordo's Banana Completed??? | Page 3 | Opel GT Forum, opelgt.com
  18. Gordo's Banana Completed??? | Page 4 | Opel GT Forum, opelgt.com
  19. ALB-Bremsdruckregler-Grundeinstellung,, sprinter-forum.de
  20. Was ist das für ein Teil? VW LT Bj.2003, sprinter-forum.de
  21. Zusatzfedern, sprinter-forum.de